ASTM D4940 PDF

ASTM D standard describes the conductivity test used to assess the presence of ASTM D test method consists in combining equivalent volumes of. ASTM D – Standard Test Method for Conductimetric Analysis of Water Soluble Ionic Contaminatio. ASTM D Standard Test Method for Conductimetric Analysis of Water Soluble Ionic Contamination of Blast Cleaning Abrasives.

Author: Nilkree Kajilmaran
Country: Hungary
Language: English (Spanish)
Genre: Sex
Published (Last): 22 December 2010
Pages: 481
PDF File Size: 12.47 Mb
ePub File Size: 5.26 Mb
ISBN: 750-4-87705-771-1
Downloads: 46334
Price: Free* [*Free Regsitration Required]
Uploader: Nikogul

Elcometer Abrasive Soluble Salt Test Kit – ASTM D

Last previous edition approved in as D – Thus, it provides an indication of ionic corrosion potential. This test is useful in establishing the cleanliness of the abrasive at the jobsite. However, the bias introduced by this factor is in the asttm direction. The ASTM method is well suited for use in the?

Abrasives used for blast cleaning surfaces can astmm contaminated with soluble salts due to the source or the re-use of the blasting media. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility.

NOTE 3β€”In general the cell constant is not greatly affected by variations in the strength of the KCl solution, but, for greater accuracy, measurements should be made at or near the speci?

Another method is to stir the solution with a clean thermometer while the vessel is warmed or cooled by an external source.

Either a dip-type, pipet-type, or cup-type cell may be used. Originally approved in Elcometer Bresle Salt Kit A range of products to test the level of contaminants on the surface. That is, high conductivity due to a lower pH of the contamination would normally indicate greater corrosion potential. The ASTM method allows a user to measure a loose packed volume of abrasive and mix that abrasive with an equal volume of reagent water.

  BELDEN 8102 PDF

A measured volume of the abrasive is mixed with the same volume adtm water and agitated to allow any soluble salts to dissolve in the water.

Elcometer E Conductivity Meter, ml In the ASTM Method the weight of the abrasive is not known; this makes it impossible to assess the ratio between conductivity values determined using this test method procedure and those determined using the ISO procedure.

This contamination of the abrasive can transfer to the steel surfaces being blasted, where it may accelerate corrosion. A volume comparison is more closely related to surface area of the abrasives than is a weight comparison.

Method to Method Comparison: When no markings distinguishing between units of production appear, take samples from the different packages in 8. The resulting slurry is allowed to settle and the filtered water can then be tested using a conductivity meter.

The Society for Protective Coatings, 40 24th St. Current edition approved January 10, A superscript epsilon e indicates an editorial change since the last revision or reapproval. Unless otherwise indicated, it is intended that all reagents conform to the speci?

This 1 This speci? This standard is subject to revision asrm any time by the responsible technical committee and must be reviewed every? However, slags quenched with seawater or other contaminated water, contain high amounts of ionic material as does seashore sand. This constant should be checked periodically, one method being as follows: The ISO zstm is well suited to use in a laboratory setting but is poorly suited to use in the?

  D641 BLR INSTRUCTIONS PDF

Elcometer E Conductivity Meter An entry level conductivity meter, is d440 for measuring soluble salt concentration and electric conductivity EC of solutions.

Elcometer 138 Abrasive Soluble Salt Test Kit – ASTM D4940

The ranked order correlation between the two methods was unity. Calibration and Standardization 8. Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend. The Elcometer Abrasive Soluble Salt Test Kit provides all that is needed to carry out d494 test in the field or in the laboratory. NOTE 1β€”A typical value of conductivity for a high level of asfm is ? Abrasives that showed qualifying extracted salts using the ISO Procedure also showed qualifying extracted salt levels as speci?

Calculate the cell constant, K25, as follows: Elcometer Inc, Michigan Office Relocation. Summary of Test Method 3.

If you feel that your comments have not received a fair aztm you should make your views known to the ASTM Committee on Standards, at the address shown below. The conversion factor from?

It differs from this test method in two major areas: Test the samples separately.

Author: admin